TEEM-Lab: Collaborative, Responsive, Interactive, Result-oriented    

Find below an overview of the testing resources that are available to you, this list is not exhaustive. If you need specific equipment or you don’t know exactly how to carry out your tests, consult the team of experts at TEEM-Lab, they will be able to advise and assist you.

Thermal Testing Equipment

• Ovens/aging furnaces: Ambient → 300°C
• High-capacity/high-temperature furnace: Heat treatment, annealing, tempering, etc.) up to ~800–850°C. 
• Chiller/cold plate: Indirect cooling, thermal regulation testing.Data loggers/temperature acquisition: Thermal profiling, multi-sensor test monitoring (depending on configuration).
• Data loggers/temperature acquisition: Thermal profiling, multi-sensor test monitoring (depending on configuration).

Environmental Testing Equipment

• Salt Spray + corrosion equipment: Corrosion assessment materials / coatings. 
• Climatic chambers: thermal cycling and relative humidity.
• Sorbonne (chemical protection) + viscometer + gel timer: Chemical compatibility, resins/varnishes rheology, frost time.
• Oil bath for probes (thermal sensor tests): Regulation & characterization hysteresis sensors.
• Rain test ramp (CSA / UL 1004): Rain / waterproofing tests according to requirements.
• Connection cabinet / motor & drive (test platform): Instrumented test setups, aging campaigns on assemblies

Electrical Testing Equipment

• PDIV / Partial discharges – SOLFAS (GRP2500 & GHV2000): DP detection, non-destructive insulation testing (stators, high-voltage equipment).
• HiPot / High voltage test: Insulation integrity testing up to ~40 kV. 
• Dielectric meter – SEFELEC DTPG500+: Dielectric strength/insulation resistance (up to 5 kV AC/6 kV DC).
• Impedance analyzer / frequency - Newton4th PSM1700: Frequency response / impedance (10 μHz 1 MHz).
• Power (x12) – 0-20V / 0-300A: Product heating regulation, instrumented test campaigns.
• Micro‑ohmmeter – Chauvin Arnoux C.A 6240: Measurement of low resistances, connection quality.
• Portable Megohmmeter – MEGGER: Isolation resistance measurement (field / lab).
• CTI / IRC – resistance to creep measurement: Behavioral evaluation of insulators (tracking) under stress.
• Hysteresis graph – B(H) curve: Magnetic properties of materials (magnets/laminations, etc.).
• Epstein frame: Characterization of magnetic sheets (curves and losses).
• Rotor magnetic field test bench: Field distribution, flow pulsations (R&D/design).
• Enameled wire tests: abrasion / thermoplasticity / adhesion / pinhole: Enamel quality, microcracks, compatibility, and electrical performance.
• ASTM D4880 / PinHole: Enamel behavior & impregnation in saline environments under stress.
  
   

Mechanical Testing Equipment

•  Traction/ compression machines – 10 kN & 100 kN (SHIMADZU) : Mechanical testing, hot testing possible (depending on configuration).
• Vibrating table (in box) + vibration benches: Simulation of high vibration stresses, endurance.
• Anderonmeter (FAG): Vibration/noise analysis of bearings, damping factor.
• Sharpy test: Impact testing (resilience) of materials.
• Packaging test ramp + drop ramp: Validation of packaging for transport/handling, impacts. 
• Cutting machine – LAM PLAN: Cutting of samples, metallographic preparation.
• Polishing machines – PRESI: Preparation and finishing of samples.
• High-resolution digital microscope (Keyence VHX) + microscope/binocular: Inspection, assessment, 2D/3D measurements depending on options.
• Durometer (Shore): Hardness measurement of polymers/elastomers.
• Permascope: Mesure d’épaisseur revêtement (peinture / traitements).
• Scales (high precision / precision): Weighing and preparing samples (KERN, OHAUS as needed).
• High-speed/rotation box (vertical and horizontal axes): Rotation/centrifugal force testing, rotating environments.
• Climatic chambers (BIA / CLIMATS / Friocell…): -60°C to +180°C, humidity up to 99% (depending on chamber).