German - Germany

Meltech Cuts Costs and Maintenance on Inline Plastics Coiling Machines

by switching from DC to AC drives from Control Techniques

Meltech Cuts Costs and Maintenance on Inline Plastics Coiling Machines

DEC 15, 2013

One of Europe’s leading manufacturers of extrusion, winding and coiling equipment for the metals, wire / cable and plastics industries has taken the design of its semi-automatic plastics inline coiling equipment one step further with the elimination of a separate PLC and reduced the need for maintenance by switching from DC to an intelligent AC drives solution from Control Techniques.

Meltech Engineering Ltd of Blackburn in Lancashire has taken a fresh look at the control system for its semi-automated plastics coiling machines, versatile winders that can coil a variety of small plastic profiles such as the fine plastic tubes used in aerosols.  Their chosen solution to simplify and improve reliability in one go has been to switch to Unidrive SP AC drives, four in total for each coiler, each drive featuring a powerful programmable on board plug-in SM Applications module – a PLC in its own right.

This has eliminated the need for a costly separate controlling PLC and removed a considerable amount of wiring between the PLC and the drives, cutting both build time and an area of potential weakness, thus enhancing machine reliability.

The Meltech semi-automatic plastic coiler features two reels mounted on a transfer disc.  When the active winder is full, the disc is rotated 180° and the extrusion is automatically transferred and attached onto the empty reel to allow continuous uninterrupted operation of the extrusion line.  Depending on the product to be wound, the machine can operate at line speeds of up to 300m/min on a variety of drum and coil sizes.

The winding drives are both 1.1kW Unidrive SP AC drives in speed control, the transfer disc is controlled by a 1.5kW Unidrive SP in open-loop vector mode and the traverse is controlled by a 0.37kW Unidrive SP in servo mode twinned with a Control Techniques Unimotor FM servo motor.

All four drives communicate with Control Techniques’ own high-speed network, CT-Net, facilitated by the SM-Applications Plus modules in each drive. The entire machine application control program is on just one of these units.

We were looking for ways to cut manufacturing costs whilst maintaining or improving reliability and decided to switch from DC to AC,” says Meltech’s Engineering Manager, Andrew Procter. “Whilst the switch to AC has brought a number of benefits, the selection of Unidrive SP drives has brought even more. 

 The feed for the winder drives is by slip rings.  We now only need six slip-rings for the three phases on each motor – we needed eight before, which has cut build cost, improved reliability and cut some maintenance.  In our development phase we considered whether we still needed encoder feedback for accurate speed control – but found that the Unidrive SP’s open-loop vector mode performance enabled us to eliminate the encoders, again saving costs and improving reliability.  All users will understand that AC means less maintenance than DC, so there’s another saving here.

“However, perhaps the biggest saving has been in the elimination of the PLC. The programmable SM-Apps modules have more than enough intelligence to run the machine.  We found them very straightforward to programme, any one who is familiar with regular PLC programming will have no problems in adapting this approach.  And all of the drives are an identical platform, so we don’t need to mix and match different drives and servo drives.”

Meltech engineers used CT-Soft, Control Techniques’ software configuration tool for setting up and to parameterise the drives and SyptPro for programming the PLC machine control program.

The Unidrive SP ‘solutions platform’ AC variable speed drive range spans 0.37kW right up to 1.9MW.  It is configurable into five operating modes – open and closed loop, vector, servo and regenerating modes. With a range of plug-in module options, its on-board PLC can be supplemented with programmable and specialist feedback and communication modules.  The SM Applications Plus module provides programmable automation from simple start/stop sequencing of a single drive to more complex machine and motion control applications.  The module gives high-speed drive-to-drive communications via CT-Net and extremely fast I/O.

Less wiring, fewer components and identical drive platforms all adds up to a better, more reliable product requiring less maintenance. It’s a good news story!” concludes Andrew Procter.

Meltech machines offer continuous winding of multiple profiles enabling significant productivity benefits compared with manual handling.  Readily integrated with plastic extrusion production operations, the Meltech machines feature touch-screen control and industry-leading reliability.

Check our brochure "Intelligent drives just went genius" to find which Control Techniques general purpose drives have integrated PLC.
Check our brochure "Upgrading from Commander SK to Unidrive M" to find the benefits of upgrading from Commander SK and Unidrive SP AC drives to Unidrive M
This website uses cookies to ensure you get the best experience on our website. Learn More